Developed by Airbus, Daher and Safran, the EcoPulse hybrid-electric demonstrator used an 800VDC system delivering up to 350kW to support six wing-mounted electric propellers (source: Airbus)
Silicon carbide power electronics, insulation and fault protection must work together in high-voltage flights, writes Barry Mansfield.
Cabin pressurisation, anti-icing, engine starting, pumps, brakes and actuators are increasingly going electric, while hybrid propulsion is set to push aircraft power demand higher still. But carrying more current requires heavier cabling, adding weight that aircraft designers can ill afford.
In response, the sector is now moving towards higher-voltage power systems.
A 1MW system draws 2,500A at 400V, 1,250A at 800V and 1,000A at 1kV. Raising the voltage allows the same power to flow at a lower current. This reduces heat generated in the cables, cutting energy losses and the need for cooling.
Nasa is testing kilovolt-class power systems, while Airbus’s €50m LEIA programme aims to demonstrate an integrated high-voltage electrical system on the ground by 2027.
However, operating at 800V creates a particular vulnerability: as air pressure falls with altitude, the risk of partial discharge, corona and electrical arcing increases. Safran’s Pierre-Julien Sonnette says 800V is “much higher than what we’re used to”, requiring engineers to “entirely redesign the electrical system”.
When air stops being an insulator
As aircraft climb, falling air pressure can make electrical breakdown between conductors more likely. The breakdown voltage depends on air pressure and conductor spacing, a relationship described by Paschen’s law.
Nasa cites a minimum DC breakdown voltage of about 327V in air under specific conditions, compared with around 230V RMS for 400Hz AC. At 800V careful insulation design and adequate electrical clearances are therefore vital to prevent arcing at altitude.
Insulation can also deteriorate over time. Tiny air pockets, contamination and manufacturing defects can create areas of intense electrical stress. Vibration, repeated heating and cooling can worsen these weak points, lowering the voltage at which partial discharge begins.
This threshold is called partial-discharge inception voltage (PDIV). The lower it falls, the more easily discharge can occur. In 2025 Nasa found that thermal cycling reduced PDIV in coated and resin-encased magnet wire after just a few cycles.
SiC raises the stakes
Silicon Carbide (SiC) is helping aircraft designers push voltage and power density higher. Compared with conventional silicon devices, wide-bandgap switches can operate at higher temperatures and switch faster while cutting conversion losses.
Ampaire’s hybrid-electric Cessna 337, part of its flight-test fleet based at Camarillo Airport in California, was used to test an 800V, 250kW silicon carbide (SiC) inverter (source: Ampaire)
This helps to shrink cooling hardware and some magnetic components, allowing more power to be packed into less space and weight.
In June 2026 GE Aerospace and Wolfspeed agreed to develop standards for power modules using 10kV SiC switches, potentially making future converters smaller, lighter and more efficient.
Wenzhi Zhou, who led Coventry University’s study of partial discharge in electrified-aircraft machines, says wide-bandgap devices can switch around 10-times faster than silicon, with voltage slew rates, or rates of voltage change, of 30–50kV/µs.
However, these rapid voltage changes stress motor windings and insulation, increasing the risk of partial discharge and making that discharge harder to distinguish from switching noise.
Engineers are addressing this through active dv/dt filtering and improved discharge detection.
The weight of integration
Researchers at the universities of Arkansas and Illinois developed an 800V, 250kW inverter for Ampaire using custom 1,200V SiC modules. It was successfully flight-tested in a Cessna 337 at Camarillo Airport, California.
A Nasa engineer works on a dynamometer at the agency’s Electric Aircraft Testbed in Sandusky, Ohio, where megawatt-scale electric propulsion systems are tested under simulated flight-altitude conditions (source: Nasa)
This inverter achieved about 60kW/litre and 30kW/kg, using pin-fin baseplates to transfer heat directly into the coolant.
The project shows why packaging, isolation, cooling, interconnects and electromagnetic interference must be considered together, while every added gram erodes the weight savings higher voltage is meant to deliver.
The same pressure to save weight applies to insulation. Greater creepage and clearance distances, thicker insulation and shielding all compete for limited space and weight.
Nasa has developed boron nitride insulation composites that can more than double thermal conductivity while maintaining dielectric strength. Better heat transfer could allow thinner, lighter insulation around cables and windings.
An Airbus A380 contains around 300 miles of wiring. At that scale, even small reductions in insulation thickness and cable mass can save significant weight.
Protection in microseconds
At megawatt power levels, protection systems must clear faults rapidly to limit damage from electrical arcing. To meet this need, Nasa’s RTAPS programme developed a 1.2kV, 1kA solid-state DC circuit breaker for electrified aircraft that can cut off fault current in under 100µs in simulated 35,000ft conditions, while operating at more than 99.5% efficiency.
Nasa’s Electric Aircraft Testbed in Sandusky, Ohio, tests megawatt-scale electric aircraft powertrains under simulated flight-altitude conditions, allowing engineers to assess performance and reliability before flight (source: Nasa)
On the detection side, Fraunhofer IISB and FAU Erlangen-Nürnberg are developing faster ways to identify insulation faults. Their hardware-based unit can recognise critical faults in less than 1.5ms, then command an electronic or pyrotechnic fuse to disconnect the faulty circuit.
Safran’s OSYRYS project, part of the EU’s Clean Aviation programme, targets high-voltage and thermal-system validation by 2028, with further demonstrations and a certification-readiness roadmap to follow by 2030. Clean Aviation’s goal is hybrid-electric regional aircraft entering service by 2035.
Barry Mansfield is a business and technical writer
See: Littelfuse automotive TVS diodes deliver low, flat-clamping voltage


