Acer is rolling out a fresh ProDesigner display lineup aimed at photographers, video editors, and hybrid creators, with three new models now listed as B&H exclusives in the US. The headline act is the PE320QXT, a 31.5-inch 6K panel with full multi-touch input and stylus support, joined by a 27-inch 4K monitor with switchable refresh rates and a 16-inch portable OLED for working on the road.
Color-accurate desktop displays have become a busier category than ever, with Apple’s Studio Display sitting at one end of the creator market and the ASUS ProArt and LG UltraFine 6K lines crowding the other. Acer’s refreshed ProDesigner range slots in well below all of them on price while leaning on Calman verification, wide gamut coverage, and a feature mix you do not see at these tiers. All three displays carry Acer’s Creator Hub software for color space switching, calibration profiles, and split-screen layouts. Note that in some regions Acer markets the same panels under the ProCreator sub-brand; the US listings at B&H carry the ProDesigner naming.
Acer ProDesigner PE320QXT: 6K. Credit: AcerPE320QXT: 6K resolution meets touchscreen input
The 31.5-inch PE320QXT is the most distinctive of the three, and it is a B&H exclusive in the US market. It pairs a Quantum-Dot IPS panel at 6016 x 3384 running at 60 Hz with 10-point multi-touch and MPP 2.0 tilt-enabled stylus support, a combination that is essentially unseen at this resolution. For photo retouching, illustration, and rotoscoping, that means one fewer Wacom on the desk and a working surface large enough to keep tools docked while still leaving a full 4K-equivalent canvas for the image itself. Pixel density lands at roughly 219 PPI, well above the 140 PPI typical of 32-inch 4K monitors.
The panel is rated at 600 nits peak with VESA DisplayHDR 600 certification, a 4 ms gray-to-gray response time, and 1.07 billion displayable colors via 8-bit + FRC. Acer claims a Delta E below 1, 99% Adobe RGB, and 99% DCI-P3 coverage, with the display Calman Verified from the factory. Connectivity is broad: two HDMI 2.1 inputs, DisplayPort, USB-C with 90W power delivery, a USB-B upstream port, two USB-A 3.2 Gen 1 downstream ports, and a 3.5mm audio jack. An 8MP webcam with a microphone array sits in the bezel, and dual 5W speakers handle audio. The stand offers tilt, swivel, height, and pivot adjustment, with VESA 100 x 100 mounting and a roughly 10kg / 22lb weight for the touchscreen variant.
It is worth comparing this against the ASUS ProArt Display PA32QCV, the closest 6K IPS rival we have tested, which lands at $1,399 without touch. The PE320QXT roughly matches that price while adding the touch and stylus layer, which will be a real workflow decision for anyone weighing illustration tooling against pure color reference work. As always with IPS at this resolution, do not expect the contrast or true blacks of a QD-OLED reference like the ASUS ProArt OLED PA27USD we recently reviewed.
Acer ProDesigner PE270K. Credit: AcerA dual-mode 4K monitor in the PE270K
The 27-inch PE270K is the most conventional product in the trio, but it has one trick worth flagging. Its 3840 x 2160 IPS panel ships with what Acer calls Dynamic Frequency and Resolution: 4K UHD at 72 Hz, or Full HD 1920 x 1080 at 144 Hz. That makes it more flexible than the typical 60 Hz desktop creator panel, though editors and colorists will likely keep it locked to 4K at 72 Hz, where the extra refresh headroom helps with timeline scrubbing without dropping resolution.
Color performance is the headline. Calman verification, a quoted Delta E below 1, 99% Adobe RGB, and 96% DCI-P3 coverage put it in serious creator territory. Brightness is rated at 400 nits with VESA DisplayHDR 400 and 1.07 billion colors, while the dynamic contrast ratio is listed at 100,000,000:1 with FreeSync support and a 1 ms gray-to-gray response time. The panel is anti-glare, and the I/O suite includes two DisplayPort inputs, HDMI, USB-C with DP Alt Mode, a USB-B upstream port, and two USB-A 3.2 Gen 1 downstream ports. There is no built-in webcam on this model, but the price reflects that.
For a working colorist or editor, the PE270K reads more like a daily-driver edit display than a critical reference monitor. The 96% DCI-P3 figure is respectable but does not match the OLED references we have measured recently, where black-level performance ultimately wins for HDR grading. It is, however, priced like a consumer monitor while behaving like a professional one, and that is the point. As a second screen for waveform monitors, bins, and scopes alongside a higher-grade primary, it makes a lot of sense.
Acer ProDesigner PE160W. Credit: AcerA 16-inch portable OLED in the PE160W
Rounding out the line is the PE160W, a 16-inch portable OLED in a 16:10 form factor at WUXGA (1920 x 1200) resolution. OLED in a portable monitor is the obvious draw here: true blacks, per-pixel emission, and a 1 ms gray-to-gray response time, with brightness rated at 300 nits and a 100,000,000:1 dynamic contrast ratio. Acer cites 95% DCI-P3 coverage and Delta E below 2, with Calman verification, although the color depth here is 16.7 million (8-bit) rather than the 1.07 billion quoted on the other two models.
Connectivity is limited to HDMI, USB-C, and a 3.5mm audio jack, with USB-C handling power and video over a single cable for laptop-side setups. For a DIT pulling stills off a roving cart, a colorist running QC on the road, or an editor who occasionally needs a second screen at a coffee shop, that single-cable workflow is the value proposition. We have written before about the role of portable displays in field editing, including Johnnie’s go-to portable editing set-up, and the PE160W lands in that category at a notably lower price than most rivals.
The resolution choice is the obvious trade-off. At 1920 x 1200, it is not going to pixel-peep on a 4K timeline, so it is more about reference and scrubbing than precision color review. For those use cases, though, the OLED contrast and 95% P3 coverage are competitive with portable monitors costing two or three times as much.
Pricing and availability
All three displays are listed as B&H exclusives in the US, with staggered ship dates in June. The PE320QXT 6K touchscreen carries an estimated ship date of June 8 at $1,499.99. The PE270K 4K is expected June 1 at $449.99, and the PE160W 16-inch portable OLED is targeted for June 22 at $249.99. The full Acer category page at B&H lists all three models, and full specifications for the broader range are on the Acer ProDesigner monitor page.
Where do these new Acer ProDesigner displays fit in your workflow? Does the 6K touchscreen pull you in, or do you still reach for OLED references? Don’t hesitate to let us know in the comments below!