The LimeSDR Micro M.2 2280 software-defined radio (SDR) card combines an NXP LA9310 baseband processor and a Lime Microsystems LMS7002M transceiver, and targets integration into portable or embedded solutions with a spare M.2 PCIe Gen3 x1 socket.
The module is offered in a 1T2R configuration by default, but can be expanded to 1T4R via an FPC connector, supports a 30 MHz to 3.8 GHz frequency range, and up to 100 MHz bandwidth. Target applications include 4G LTE/5G, future RAN research, custom user equipment/modems, drone communications, IoT, satellite communications, and custom waveform generation.
LimeSDR Micro M.2 SDR card specifications:
SoC – NXP LA9310 programmable baseband processor
Vector Signal Processing Accelerator (VSPA) Gen 2 up to 80 GFLOPs
Control Processor – Arm Cortex-M4 at up to 307 MHz
Storage – 512 Kbit EEPROM memory for NXP LA9310 initial configuration
RF
Lime Microsystems LMS7002M RF transceiver
Channels – 1T2R expandable to 1T4R via two analogue baseband inputs on an FPC connector (see Connectors section below)
Frequency Range – 30 MHz to 3.8 GHz
Bandwidth – 100 MHz TDD or half-duplex operation and 50 MHz FDD
Analogue Filtering – 0.75 – 100 MHz
Sample Rate – Up to 160 Msps half-duplex (Tx or Rx) and TDD, and up to 61.44 Msps FDD
Connectors
3x MHF4 RF (TX, RX1 & RX2)
15-pin FPC external analogue I/Q baseband input (RX3 & RX4)
Host Interface – PCIe Gen 3 x1 via M.2 Key -B+M edge connector
I/O expansion via 8-pin FPC connector
4x GPIOs 3.3V on GPIO connector
I2C on GPIO connector (shared with on-board devices)
Sensor – TMP1075NDRLR temperature sensor
Clock Subsystem
Rakon E6245LF 30.72 MHz VCTCXO
VCTCXO may be tuned by an onboard 16-bit DAC
Reference clock input and output connector
4x MHF4 clock and PPS I/O
Misc
2x Green LEDs
Optional GNSS Receiver: Antenova M10578-A3 3 for location, time of day, and generating a VCTCXO DAC value. A future firmware update might add GSPDO support (TBC)
Power Supply – 3.3V via M.2 edge connector
Dimensions – 80 x 22 mm; note: the card may not be suited to installation in certain space-constrained systems, e.g., laptops, due to the non-standard module height of up to ~4mm from the PCBA top side.
LimeSDR Micro components and ports
NXP LA9310 (left) and LimeSDR Micro (right) block diagrams
LimeMicro has offered SDR solutions based on the LMS7002M RF transceiver for years, but they were all FPGA-based so far. They’ve now switched to the NXP LA9310 ultra-low-power baseband processor for applications needing to meet specific size, weight, and/or power requirements.
It’s still 100% programmable, and the company points to the NXP LA9310 Reference Manual and VSPA2 Instruction Set Manual both available without NDA, open source VSPA kernels for functions such as FFT, inverse FFT, CRC generation, FIR filters, mixer, and modulation/demodulation (some compatible with MATLAB), as well as the existing documentation for the LMS7002M chip which is supported by the Lime Suite NG driver stack and the wider SDR ecosystem with integration with projects such as SoapySDR, GNU Radio, Amarisoft 4G/5G, OpenAirInterface, and srsRAN. The company will also release the hardware design for the M.2 module, and the DSP firmware and Arm firmware have already been released on GitHub.
LimeFEA HF Micro
The company also designed the LimeFEA HF Micro to add a third receive path with a frequency range of 0 – 30 MHz to LimeSDR Micro with the following key features.
Medium Wave (MW) broadcast notch filter
Band filters
0 – 2 MHz LPF
2 – 12 MHz BPF
12 – 30 MHz BPF
90 dB gain
72 dB programmable step attenuation
5x MHF4 to SMA transition
TDD switching out
LimeSDR Micro Pro
Two other products are the LimeSDR Micro Pro, which combines the LimeSDR Micro and the LimeFEA HF Micro to provide a USB4 (40 Gbps mode only) peripheral with an aluminum enclosure, and the LimeFEA M.2 2280 full-size PCIe x4 card with a 2×2 MIMO RF front-end (RFE), which integrates low-noise amplifiers in the receive paths (100 MHz to ~4 GHz receive frequency range) and power amplifier (PA) drivers in the transmit paths (100 MHz to 6 GHz transmit frequency range).
LimeFEA M.2 2280
Lime Microsystems had launched the LimeSDR Micro M.2 SDR card and associated products on Crowd Supply with a $100,000 funding target. Rewards start at $199 for the LimeSDR Micro basic and $299 for the LimeSDR Micro GNSS. A pledge of $199 is asked for the LineFEA HF Micro card, $299 for the LimeFEA M.2 2280 PCIe card, and $799 for the LimeSDR Micro Pro system. Shipping adds $8 to the US, $18 to the rest of the world, and deliveries are scheduled to start by September 30, 2026.
Jean-Luc started CNX Software in 2010 as a part-time endeavor, before quitting his job as a software engineering manager, and starting to write daily news, and reviews full time later in 2011.
Support CNX Software! Donate via cryptocurrencies, become a Patron on Patreon, or purchase goods on Amazon or Aliexpress. We also use affiliate links in articles to earn commissions if you make a purchase after clicking on those links.